UFS250 Shredding Concrete Blocks — Trailer-Mounted Working Footage

Working footage of the UPSEN UFS250 trailer-mounted twin-shaft shredder: a low-speed, high-torque mobile shredder on a tow frame. This page is the dedicated watch page for this video — the full machine specification and enquiry form are on the UFS250 product page.

Machine
UFS250 Trailer-Mounted Twin-Shaft Shredder
Video length
2 min 48 sec
Published
16 November 2026
Video file
ufs250-trailer-shredder-working.mp4

About this video

The clip opens on the UFS250 standing on its tow frame in an outdoor yard beside the factory buildings, with the feed hopper folded out and the discharge belt raised to stacking height. A forklift working alongside the machine keeps the hopper loaded.

The material going in is concrete blocks and demolition rubble rather than a sorted single-material stream — exactly the feed this machine is specified for. It is drawn down between two counter-rotating shafts carrying Ø680 mm cutter discs on a 1550 mm spindle at 0–50 r/min. The reduction is by shear and tearing at 160,000 N·m of reducer torque, not by impact, which is why a blocky, mixed and partly reinforced feed does not need pre-sorting or pre-cutting before it enters the hopper.

The shredded material leaves on the B800 × 8500 mm main conveyor and is stockpiled from a 2800 mm discharge height. Anything ferrous in the stream can be pulled out by the B650 × 1200 belt-type over-band magnet before the material reaches the pile, so rebar and fixings do not end up in the recycled product.

The later shots show the machine from the transport side: the tow frame, the axle and the folded conveyor, which is the configuration it travels in. At 19,500 kg and 7100 × 2200 × 2600 mm transport size, the UFS250 moves on a standard low-bed trailer or on a hook-lift frame without being stripped down.

Note on throughput: this clip was not made as a production test, so no tonnage is claimed from it. The catalogue rating for the UFS250 is 80–130 t/h on C&D debris, with 40–60 t/h on wood and 15–25 t/h on scrap metal depending on screen configuration. Where a given site lands inside that band depends on the material mix, the screen fitted and how the discharge is set.

Prices are quoted per project rather than published as a fixed figure, because the final price varies significantly with the diesel engine specified (brand, power rating and emission standard), the machine configuration (screen openings, magnet, conveyor length, CE or EPA compliance), the drive and transport arrangement (tow frame or hook-lift), and exchange-rate movement at the time of order.

Send your material, throughput requirement and destination port through the enquiry form, and we will reply with a configuration and an itemised quotation.

Where the UFS250 is used

Typical applications

  • Construction and demolition waste reduction before screening
  • Transfer stations and recycling yards with no fixed plant
  • Bulky waste and mixed commercial waste volume reduction
  • Wood, pallet and biomass size reduction
  • Scrap metal pre-shredding ahead of separation

Raw materials handled

  • C&D debris, concrete block and mixed rubble
  • Wood, pallets and green waste
  • Scrap metal and light ferrous
  • Commercial and bulky waste

Common questions about the UFS250

What does this video of the UFS250 show?

It runs 2 min 48 sec and shows the UFS250 shredding concrete blocks and demolition rubble in an outdoor yard, the discharge belt stockpiling shredded material, and the machine in its transport configuration. It is working video 1 published for the UFS250. The full specification and enquiry form are on the UFS250 product page.

Does the UFS250 need a crane or a hook-lift truck?

No crane. The machine sits on a tow frame with its own axle, so it can be towed on a standard low-bed trailer, and the frame is also built to be picked up by a hook-lift unit. Transport size is 7100 × 2200 × 2600 mm at 19,500 kg.

What capacity does the UFS250 have?

The catalogue rating is 80–130 t/h on C&D debris, 40–60 t/h on wood and 15–25 t/h on scrap metal, with a ≤150 mm discharge and a maximum feed size of 300 × 2800 mm. No tonnage is claimed for the footage on this page because the clip was not a production test.

Does the UFS250 come with EU conformity documentation?

The UFS250 is supplied with EU conformity documentation; the delivery route is confirmed with your order.

More mobile shredder working videos

Get a price for the UFS250

Tell us your material, required output and site conditions — we will reply with a configuration and quotation. The UFS250 is available for sale worldwide, and EU conformity documentation is supplied with every unit.

Email mail@upsen.cn  or call / WhatsApp +8615333827088.