UJC503 on Demolition Concrete — German Site Footage
Working footage of the UPSEN UJC503 tracked mobile jaw crusher on a demolition site in Germany. The camera sits at the discharge end: it follows the recycled product off the belt and onto the ground, then cuts into the jaw chamber and along the side of the machine. This page is the dedicated watch page for this video — the full machine specification and enquiry form are on the UJC503 product page.
About this video
A UJC503 working demolition rubble at a site in Germany in 2025. The feed is what comes out of a building strip-out: grey concrete, brick, tile and mortar. The brick fraction is still recognisable in the finished pile as the red pieces scattered through it.
The clip is shot from the discharge end rather than from the machine as a whole, and for this page that is the useful angle. On a 10–30 t/h jaw the question buyers actually ask is what the recycled product looks like and whether it will be taken away as aggregate or rejected as waste. Here it is on the belt: a graded mix from fines up to fist-sized lumps, dropping into a loose heap that a wheeled loader can move without re-handling.
The camera goes into the jaw chamber partway through, then runs along the discharge belt frame. Plate condition and belt tracking are both visible, and the machine is working the pile for the whole clip rather than being run empty for the camera.
Two honest limits. It was shot vertically on a phone and the file we hold is 480 × 854 px, so it is softer than the other UJC503 videos on this site. And no throughput was measured on this job, so the capacity stated here is the catalogue band of 10–30 t/h and nothing more precise. We would rather publish a soft clip with a true number than a sharp one with an invented number.
For buyers comparing options: this machine appears in 2 other working videos on this site — see the links below. The full specification table and EU conformity documentation are on the UJC503 product page.
Send your throughput, feed material, site conditions and destination port through the enquiry form, and we will reply with a configuration and an itemised quotation.
UJC503 key specifications
Where the UJC503 is used
Typical applications
- Quarry primary crushing of granite, basalt and limestone
- Reinforced concrete and demolition debris recycling
- Road and railway ballast production
- Contract crushing jobs that move between sites
Raw materials handled
- Granite, basalt and river stone
- Reinforced concrete with rebar
- Demolition rubble and C&D debris
- Quarry-run rock and ballast
Where to compare the UJC503
The UJC503 is one of 12 mobile jaw crushers in the UPSEN range, 6 to 500 t/h, with maximum feed openings from 180x300 mm up to 650 mm. Capacity, maximum feed size and total weight are listed side by side.
Common questions about the UJC503
What does video 3 of the UJC503 show?
This clip runs 50 sec. It is working video 3 of 3 published for the UJC503, shot at the discharge end on a demolition site in Germany in 2025. The full specification and enquiry form are on the UJC503 product page.
What was the output on the German job?
No throughput measurement was taken on this job, so none is quoted. The UJC503 is rated at 10-30 t/h; where a site figure has actually been weighed, it is stated on the page for that video.
What is the discharge range of the UJC503?
10-70 mm, set by the closed-side opening of the jaw. Opening the setting widens the product and raises tonnes per hour; closing it does the reverse.
What is the capacity of the UJC503?
The UJC503 is rated at 10-30 t/h. Achieved output depends on the feed material, its moisture content and how the machine is set up.
How much does a UJC503 weigh?
The UJC503 has an operating weight of 4,300 kg.
More videos of this machine
UJC503 Tracked Jaw Crusher — Working Video 1
1 min 19 s · demolition waste, Henan
More mobile crusher working videos
Get a price for the UJC503
Tell us your feed material, required output and site conditions — we will reply with a configuration and quotation. The UJC503 is available for sale worldwide, and EU conformity documentation is supplied with every unit.
Email mail@upsen.cn or call / WhatsApp +8615333827088.